We can pick the correct slice index directly from the ID3D11VideoDecoderOutputView
casted from data[3].
Signed-off-by: Anton Khirnov <anton@khirnov.net>
Certain hardware decoding APIs are not guaranteed to be thread-safe, so
having the user access decoded hardware surfaces while the decoder is
running in another thread can cause failures (this is mainly known to
happen with DXVA2).
For such hwaccels, only allow the decoding thread to run while the user
is inside a lavc decode call (avcodec_send_packet/receive_frame).
This is in the same the same vein as 380146924e.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
Signed-off-by: Martin Storsjö <martin@martin.st>
The decoding buffer index expected by D3D11VA is the one from the
ID3D11Texture2D not the one from the ID3D11VideoDecoderOutputView array
in AVD3D11VAContext.
Otherwise, when providing decoder slices that do not start from 0,
pictures appear in bogus order. For an invalid index crashes and
image corruption can occur.
Signed-off-by: Diego Biurrun <diego@biurrun.de>
While it is less featureful (and slower) than the built-in H264
decoder, one could potentially want to use it to take advantage
of the cisco patent license offer.
Signed-off-by: Martin Storsjö <martin@martin.st>
Currently it's exported as AVFrame.pkt_pts, which is also the only use
for that field. The reason it is done like this is that lavc used to
export various codec-specific "timing" information in AVFrame.pts, which
is not done anymore.
Since it is confusing to the callers to have a separate field which is
used only for decoder timestamps and nothing else, deprecate pkt_pts and
use just AVFrame.pts everywhere.
This function is supposed to "reset" a codec context to a clean state so
that it can be opened again. The only reason it exists is to allow using
AVStream.codec as a decoding context (after it was already
opened/used/closed by avformat_find_stream_info()). Since that behaviour
is now deprecated, there is no reason for this function to exist
anymore.
Since AVCodecContext contains a lot of complex state, copying a codec
context is not a well-defined operation. The purpose for which it is
typically used (which is well-defined) is copying the stream parameters
from one codec context to another. That is now possible with through the
AVCodecParameters API. Therefore, there is no reason for
avcodec_copy_context() to exist.
Register mmaldec as mpeg2 decoder. Supporting mpeg2 in mmaldec is just a
matter of setting the correct MMAL_ENCODING on the input port. To ease the
addition of further supported mmal codecs a macro is introduced to generate
the decoder and decoder class structs.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: wm4 <nfxjfg@googlemail.com>
Signed-off-by: Anton Khirnov <anton@khirnov.net>
This can only be used if the input data happens to be laid out
exactly correctly.
This might not be supported on all encoders, so only enable it
with an option, but enable it automatically on raspberry pi,
where it is known to be supported.
Signed-off-by: Martin Storsjö <martin@martin.st>
The raspberry pi uses the alternative API/ABI for OMX; this makes
such builds incompatible with all the normal OpenMAX implementations.
Since this can't easily be detected at configure time (one can
build for raspberry pi's OMX just fine using the generic, pristine
Khronos OpenMAX IL headers, no need for their own extensions),
require a separate configure switch for it instead.
The broadcom host library can't be unloaded once loaded and started;
the deinit function that it provides is a no-op, and after started,
it has got background threads running, so dlclosing it makes it
crash.
Signed-off-by: Martin Storsjö <martin@martin.st>
Until now, the decoding API was restricted to outputting 0 or 1 frames
per input packet. It also enforces a somewhat rigid dataflow in general.
This new API seeks to relax these restrictions by decoupling input and
output. Instead of doing a single call on each decode step, which may
consume the packet and may produce output, the new API requires the user
to send input first, and then ask for output.
For now, there are no codecs supporting this API. The API can work with
codecs using the old API, and most code added here is to make them
interoperate. The reverse is not possible, although for audio it might.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
This API is intended to allow passing around codec parameters without
using full AVCodecContext (which also contains codec options and
encoder/decoder state).
The b_frame_strategy option is only used by mpegvideoenc, qsv, x264, and
xavs, while b_sensitivity is only used by mpegvideoenc.
These are very codec-specific options, so deprecate the global variants.
Set proper limits to the maximum allowed values.
Signed-off-by: Vittorio Giovara <vittorio.giovara@gmail.com>
These variables are coming from mpegvideoenc where are supposedly used
as bit counters on various frame properties. However their use is
unclear as they lack documentation, are available only from a very small
subset of encoders, and they are hardly used in the wild. Also frame_bits
in aacenc is employed in a similar way.
Remove this functionality from AVCodecContex, these variable are mostly
frame properties, and too few encoders support setting them with anything
useful.
Signed-off-by: Vittorio Giovara <vittorio.giovara@gmail.com>
Most option values are simply unused or ignored and in practice the
majory of codecs only need to check whether to enable rle or not.
Add appropriate codec private options which better expose the allowed
features.
Signed-off-by: Vittorio Giovara <vittorio.giovara@gmail.com>
This function returns the encoded data of a frame, one slice at a time
directly when that slice is encoded, instead of waiting for the full
frame to be done. However this field has a debatable usefulness, since
it looks like it is just a convoluted way to get data at lowest
possible latency, or a somewhat hacky way to store h263 in RFC-2190
rtp encapsulation.
Moreover when multi-threading is enabled (which is by default) the order
of returned slices is not deterministic at all, making the use of this
function not reliable at all (or at the very least, more complicated
than it should be).
So, for the reasons stated above, and being used by only a single encoder
family (mpegvideo), this field is deemed unnecessary, overcomplicated,
and not really belonging to libavcodec. Libavformat features a complete
implementation of RFC-2190, for any other case.
Signed-off-by: Vittorio Giovara <vittorio.giovara@gmail.com>
This side data type is meant to be added to AVStream side data.
A fallback track indicates an alternate track to use when the
current track can not be decoded for some reason. e.g. no
decoder available for codec.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
