FFmpeg/doc/ffmpeg_powerpc_performance_evaluation_howto.txt
Guillaume Poirier 7bb79b442c MONster is no longuer shipped with CHUD, as it's been superseeded by Shark
Originally committed as revision 6174 to svn://svn.ffmpeg.org/ffmpeg/trunk
2006-09-05 11:43:04 +00:00

173 lines
5.6 KiB
Plaintext

FFmpeg & evaluating performance on the PowerPC Architecture HOWTO
(c) 2003-2004 Romain Dolbeau <romain@dolbeau.org>
I - Introduction
The PowerPC architecture and its SIMD extension AltiVec offer some
interesting tools to evaluate performance and improve the code.
This document tries to explain how to use those tools with FFmpeg.
The architecture itself offers two ways to evaluate the performance of
a given piece of code:
1) The Time Base Registers (TBL)
2) The Performance Monitor Counter Registers (PMC)
The first ones are always available, always active, but they're not very
accurate: the registers increment by one every four *bus* cycles. On
my 667 Mhz tiBook (ppc7450), this means once every twenty *processor*
cycles. So we won't use that.
The PMC are much more useful: not only can they report cycle-accurate
timing, but they can also be used to monitor many other parameters,
such as the number of AltiVec stalls for every kind of instruction,
or instruction cache misses. The downside is that not all processors
support the PMC (all G3, all G4 and the 970 do support them), and
they're inactive by default - you need to activate them with a
dedicated tool. Also, the number of available PMC depends on the
procesor: the various 604 have 2, the various 75x (aka. G3) have 4,
and the various 74xx (aka G4) have 6.
*WARNING*: The PowerPC 970 is not very well documented, and its PMC
registers are 64 bits wide. To properly notify the code, you *must*
tune for the 970 (using --tune=970), or the code will assume 32 bit
registers.
II - Enabling FFmpeg PowerPC performance support
This needs to be done by hand. First, you need to configure FFmpeg as
usual, but add the "--powerpc-perf-enable" option. For instance:
#####
./configure --prefix=/usr/local/ffmpeg-svn --cc=gcc-3.3 --tune=7450 --powerpc-perf-enable
#####
This will configure FFmpeg to install inside /usr/local/ffmpeg-svn,
compiling with gcc-3.3 (you should try to use this one or a newer
gcc), and tuning for the PowerPC 7450 (i.e. the newer G4; as a rule of
thumb, those at 550Mhz and more). It will also enable the PMC.
You may also edit the file "config.h" to enable the following line:
#####
// #define ALTIVEC_USE_REFERENCE_C_CODE 1
#####
If you enable this line, then the code will not make use of AltiVec,
but will use the reference C code instead. This is useful to compare
performance between two versions of the code.
Also, the number of enabled PMC is defined in "libavcodec/ppc/dsputil_ppc.h":
#####
#define POWERPC_NUM_PMC_ENABLED 4
#####
If you have a G4 CPU, you can enable all 6 PMC. DO NOT enable more
PMC than available on your CPU!
Then, simply compile FFmpeg as usual (make && make install).
III - Using FFmpeg PowerPC performance support
This FFmeg can be used exactly as usual. But before exiting, FFmpeg
will dump a per-function report that looks like this:
#####
PowerPC performance report
Values are from the PMC registers, and represent whatever the
registers are set to record.
Function "gmc1_altivec" (pmc1):
min: 231
max: 1339867
avg: 558.25 (255302)
Function "gmc1_altivec" (pmc2):
min: 93
max: 2164
avg: 267.31 (255302)
Function "gmc1_altivec" (pmc3):
min: 72
max: 1987
avg: 276.20 (255302)
(...)
#####
In this example, PMC1 was set to record CPU cycles, PMC2 was set to
record AltiVec Permute Stall Cycles, and PMC3 was set to record AltiVec
Issue Stalls.
The function "gmc1_altivec" was monitored 255302 times, and the
minimum execution time was 231 processor cycles. The max and average
aren't much use, as it's very likely the OS interrupted execution for
reasons of its own :-(
With the exact same settings and source file, but using the reference C
code we get:
#####
PowerPC performance report
Values are from the PMC registers, and represent whatever the
registers are set to record.
Function "gmc1_altivec" (pmc1):
min: 592
max: 2532235
avg: 962.88 (255302)
Function "gmc1_altivec" (pmc2):
min: 0
max: 33
avg: 0.00 (255302)
Function "gmc1_altivec" (pmc3):
min: 0
max: 350
avg: 0.03 (255302)
(...)
#####
592 cycles, so the fastest AltiVec execution is about 2.5x faster than
the fastest C execution in this example. It's not perfect but it's not
bad (well I wrote this function so I can't say otherwise :-).
Once you have that kind of report, you can try to improve things by
finding what goes wrong and fixing it; in the example above, one
should try to diminish the number of AltiVec stalls, as this *may*
improve performance.
IV) Enabling the PMC in Mac OS X
This is easy. Use "Monster" and "monster". Those tools come from
Apple's CHUD package, and can be found hidden in the developer web
site & FTP site. "MONster" is the graphical application, use it to
generate a config file specifying what each register should
monitor. Then use the command-line application "monster" to use that
config file, and enjoy the results.
Note that "MONster" can be used for many other things, but it's
documented by Apple, it's not my subject.
If you are using CHUD 4.4.2 or later, you'll notice that MONster is
no longer available. It's been superseeded by Shark, where
configuration of PMCs is available as a plugin.
V) Enabling the PMC on Linux
On linux you may use oprofile from http://oprofile.sf.net, depending on the
version and the cpu you may need to apply a patch[1] to access a set of the
possibile counters from the userspace application. You can always define them
using the kernel interface /dev/oprofile/* .
[1] http://dev.gentoo.org/~lu_zero/development/oprofile-g4-20060423.patch
--
Romain Dolbeau <romain@dolbeau.org>
Luca Barbato <lu_zero@gentoo.org>